Home > HOWTOs > Hadoop `sysctl.conf` parameters

Hadoop `sysctl.conf` parameters

Hadoop sysctl.conf parameters.
File System
  1. fs.file-max Increase size of file handles and inode cache
 [ahmed@server ~]# echo 'fs.file-max = 943718' >> /etc/sysctl.conf
Swappiness : Do less swapping
  1. vm.dirty_ratio setting virtual memory ratio.
  2. vm.swappiness How often swap should be used. 0 is least, 60 default.
 [ahmed@server ~]# echo 'vm.dirty_ratio=10' >> /etc/sysctl.conf
[ahmed@server ~]# echo 'vm.swappiness=0' >> /etc/sysctl.conf
Connection Settings
  1. net.core.netdev_max_backlog Increase number of incoming connections backlog.
  2. net.core.somaxconn Increase number of incoming connections.
 [ahmed@server ~]# echo 'net.core.netdev_max_backlog = 4000' >> /etc/sysctl.conf
[ahmed@server ~]# echo 'net.core.somaxconn = 4000' >> /etc/sysctl.conf
TCP settings
  1. net.ipv4.tcp_sack Disable select acknowledgments
  2. net.ipv4.tcp_dsack Allows TCP to send “duplicate” SACKs.
  3. net.ipv4.tcp_keepalive_time How often TCP sends out keepalive messages when keepalive is enabled. Default: 2hours.
  4. net.ipv4.tcp_keepalive_probes How many keepalive probes TCP sends out, until it decides that the connection is broken. Default value: 9.
  5. net.ipv4.tcp_keepalive_intvl How frequently the probes are send out. Multiplied by tcp_keepalive_probes it is time to kill not responding connection, after probes started. Default value: 75sec i.e. connection will be aborted after ~11 minutes of retries.
  6. net.ipv4.tcp_fin_timeout Time to hold socket in state FIN-WAIT-2, if it was closed by our side. Peer can be broken and never close its side, or even died unexpectedly. Default value is 60sec. Usual value used in 2.2 was 180 seconds, you may restore it, but remember that if your machine is even underloaded WEB server, you risk to overflow memory with kilotons of dead sockets, FIN-WAIT-2 sockets are less dangerous than FIN-WAIT-1, because they eat maximum 1.5K of memory, but they tend to live longer. Cf.tcp_max_orphans.
  7. net.ipv4.tcp_rmem The three values setting the minimum, initial, and maximum size of the Memory Receive Buffer per connection. They define the actual memory usage, not just TCP window size.
  8. net.ipv4.tcp_wmem The same as tcp_rmem, but just for Memory Send Buffer per connection.
  9. net.ipv4.tcp_retries2 This value influences the timeout of an alive TCP connection, when RTO retransmissions remain unacknowledged. Given a value of N, a hypothetical TCP connection following exponential backoff with an initial RTO of TCP_RTO_MIN would retransmit N times before killing the connection at the (N+1)th RTO. The default value of 15 yields a hypothetical timeout of 924.6 seconds and is a lower bound for the effective timeout. TCP will effectively time out at the first RTO which exceeds the hypothetical timeout. RFC 1122 recommends at least 100 seconds for the timeout, which corresponds to a value of at least 8.
  10. net.ipv4.tcp_synack_retries Number of times SYNACKs for a passive TCP connection attempt will be retransmitted. Should not be higher than 255. Default value is 5, which corresponds to ~180seconds.
 [ahmed@server ~]# echo 'net.ipv4.tcp_sack = 0' >> /etc/sysctl.conf
[ahmed@server ~]# echo 'net.ipv4.tcp_dsack = 0' >> /etc/sysctl.conf
[ahmed@server ~]# echo 'net.ipv4.tcp_keepalive_time = 600' >> /etc/sysctl.conf
[ahmed@server ~]# echo 'net.ipv4.tcp_keepalive_probes = 5' >> /etc/sysctl.conf
[ahmed@server ~]# echo 'net.ipv4.tcp_keepalive_intvl = 15' >> /etc/sysctl.conf
[ahmed@server ~]# echo 'net.ipv4.tcp_fin_timeout = 30' >> /etc/sysctl.conf
[ahmed@server ~]# echo 'net.ipv4.tcp_rmem = 32768 436600 4194304' >> /etc/sysctl.conf
[ahmed@server ~]# echo 'net.ipv4.tcp_wmem = 32768 436600 4194304' >> /etc/sysctl.conf
[ahmed@server ~]# echo 'net.ipv4.tcp_retries2 = 10' >> /etc/sysctl.conf
[ahmed@server ~]# echo 'net.ipv4.tcp_synack_retries = 3' >> /etc/sysctl.conf
Disable IPv6 Defaults. We dont use these anyway.
 [ahmed@server ~]# echo 'net.ipv6.conf.all.disable_ipv6 = 1' >> /etc/sysctl.conf
[ahmed@server ~]# echo 'net.ipv6.conf.default.disable_ipv6 = 1' >> /etc/sysctl.conf
[ahmed@server ~]# echo 'net.ipv6.conf.lo.disable_ipv6 = 1' >> /etc/sysctl.conf
Execute below command to make it permanent.
 [ahmed@server ~]# sysctl -p
Next update limits.
 [ahmed@server ~]# echo '* - nofile 65536' >>/etc/security/limits.conf
[ahmed@server ~]# echo '* - nproc 65536' >>/etc/security/limits.conf
More Details on IPv4
 http://www.cyberciti.biz/files/linux-kernel/Documentation/networking/ip-sysctl.txt
http://www.cyberciti.biz/files/linux-kernel/Documentation/sysctl/
Advertisements
Categories: HOWTOs
  1. No comments yet.
  1. No trackbacks yet.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: